Home > Creative Solutions > Static
Sort By:
Page of 2
Hot Shots, Copper, Double Detent Balls. 10-24 or 10-32, KC5465
Hot Shots, Copper, Double Detent Balls. 10-24 or 10-32, KC5465
$9.60

Hot Shots take the Snap Sert concept two steps further by adding extra holding power with the double detent design and faster heat transfer via the copper alloy make-up intended to be used for difficult areas or complicated inserts. Recommended uses: Inserts, deep cores, hard to heat areas. Your insert (size) 10-24, 10-32, fits Norstar's 1/4-20 Snap Sert.  Hot shots come with nut and washer.
Hot Shots, Copper, Double Detent Balls, 1/4-20, KC5466
Hot Shots, Copper, Double Detent Balls, 1/4-20, KC5466
$9.60

Hot Shots take the Snap Sert concept two steps further by adding extra holding power with the double detent design and faster heat transfer via the copper alloy make-up intended to be used for difficult areas or complicated inserts.
Recommended uses: Inserts, Deep cores, hard to heat areas.

Your insert thread size 1/4-20 fits Norstar's 10-32 Snap Sert.

Hot shots come with nut and washer.
Hot Shots, Copper, Double Detent Balls, 5/16-18, KC5467
Hot Shots, Copper, Double Detent Balls, 5/16-18, KC5467
$9.60

Hot Shots take the Snap Sert concept two steps further by adding extra holding power with the double detent design and faster heat transfer via the copper alloy make-up intended to be used for difficult areas or complicated inserts.

Recommended uses:
Inserts, Deep cores, hard to heat areas.

Your insert thread size 5/16-18 fits Norstar's 1/4-20 Snap sert.  Hot shots come with nut and washer
Copper Hot Shots, Double Detents, 6mm, KC5423-MC
Copper Hot Shots, Double Detents, 6mm, KC5423-MC
$15.00

Snap Serts are a time-saving installation and release system for molded-in inserts. Manufactured in a detent ball construction, they simplify pre-molding installation with a simple push-to-install motion. Post molding is just as simple as the inserts easily slip off the holders during the normal de-molding action of the plastic part. Use of these devices eliminates the need to screw and unscrew the inserts onto a bolt.

Hot Shots take the Snap Sert concept two steps further by adding extra holding power with the double detent design and faster heat transfer via the copper alloy make-up intended to be used for difficult areas or complicated inserts.

Recommended uses: Inserts, deep cores, and hard to heat areas. Hot shots come with nut and washer.

Hot Shots, Copper, Double Detent Balls, 5mm, KC5470
Hot Shots, Copper, Double Detent Balls, 5mm, KC5470
$15.00

Hot Shots take the Snap Sert concept two steps further by adding extra holding power with the double detent design and faster heat transfer via the copper alloy make-up intended to be used for difficult areas or complicated inserts.

Recommended uses: Inserts, Deep cores, hard to heat areas.

Norstar's 5mm Snap Sert fits customer's 6mm insert.

Hot shots come with nut and washer.
Hot Shots, Copper, Double Detent Balls, 6mm, KC5471
Hot Shots, Copper, Double Detent Balls, 6mm, KC5471
$15.00

Hot Shots take the Snap Sert concept two steps further by adding extra holding power with the double detent design and faster heat transfer via the copper alloy make-up intended to be used for difficult areas or complicated inserts.

Recommended uses: Inserts, Deep cores, hard to heat areas.

Norstar's 6mm Snap Sert fits customer's 8mm insert.

Hot shots come with nut and washer.

Hot Shots, Copper, Double Detent Balls, 8mm, KC5472
Hot Shots, Copper, Double Detent Balls, 8mm, KC5472
$15.00

Hot Shots take the Snap Sert concept two steps further by adding extra holding power with the double detent design and faster heat transfer via the copper alloy make-up intended to be used for difficult areas or complicated inserts.

Recommended uses: Inserts, Deep cores, hard to heat areas.

Norstar's 8mm Snap Sert fits customer's 10mm insert.

Hot shots come with nut and washer.
Anti-Stat Dowel Pins, KC4170
Anti-Stat Dowel Pins, KC4170
$26.00

Flange Anti-Stat Dowel Pin Sets.
Our new, inexpensive easy to install Anti-Stat Dowel Pins have been designed to eliminate most, if not all the static build up in molds, which in turn, will eliminate color swirl issues.
Consists of one male and one female piece, lock washers and hex nuts.


Anti-Stat Dowel G3 Pins Kit/copper, KC4171
Anti-Stat Dowel G3 Pins Kit/copper, KC4171
$49.00

Anti-Stat Dowel G3 Pins, copper
(One male, one female piece, 2-Tabs, lock washers & HEX nuts)

Anti-Stat Dowel Pins are designed to drain buildup of static from the mold out through the arm of the machine. For retrofitting existing molds, it is necessary to install "outrigger" tabs onto your parting line. (Included as part of the retrofit kit). Directions will be sent along with the kit.

Anti-Stat Kits, KC5780
Anti-Stat Kits, KC5780
$242.00

Designed to alleviate static discharge between mold halves, which result in "pitting" on the parting line causing deterioration and shortened mold life before major rebuilding.

Added to the outside of each mold half, the kit makes contact between halves when the mold is clamped closed. Unlike the steel clamps or bolts used for clamping molds which carry a much lower thermal conductivity than aluminum, Anti-Stat Kits are made from copper alloy components which use the superior electrical conductivity of copper over both steel and aluminum to conduct the static charge around the mold and into the ground via the arm of the machine.

This outside route eliminates the path of conductivity between the mold halves at the parting line.
The result is avoiding unnecessary down time of the mold due to maintenance caused by static discharge.

Static free components

Set Includes: (1) Copper Finger Contacts; (1) Copper Finger Probes; (2) Steel Receivers to hold copper components; (2) Roll Pins; (2) Double ended threaded bolts with HEX in center; (1) Copper Wire (12 feet long and .064" diameter); (2) 1/4-20 S.S. Hex Nuts; (1) 1/4-20 X .75 Hex Head Bolt.