Intellivents

Home > Venting Products > Intellivents

Sort By:

Page of 1

Intellivent, KC401852

$1.80

Our new Intellivent uses the tested venting performance of our Supavent line and goes one step further by allowing the vent to be inserted into a 1" O.D. PTFE tube. This protects it from the problems caused by rough extraction from the plastic part and/or the mold.

This vent is designed to fit straight into the end of a PTFE tube that has been reamed to the proper diameter with our cutting tool. Now molders can employ this new venting technology without concern of tearing or wearing from rough handling.

Sample Pack of Supavents, Smartvents, Intellivents, KC401875

Sample Pack of Supavents, Smartvents, Intellivents, KC401875

$30.00

KC401875 Pack consists of (2) of the following:
KC401850 1/2" (13mm) Supavent
KC401851 3/4" (19mm) Supavent
KC401846 1" (25.4mm) Supavent
KC401855 1/2" (13mm) Smartvent
KC401858 5/16''(8mm) Smartvent
KC401857 3/4" (19mm) Smartvent
KC401856 1" (25mm) Smartvent
KC401852, 3/4" Intellivent

Intellivent/Intellitube Sample Pack - 6", KC401852-6-PK

Intellivent/Intellitube Sample Pack - 6", KC401852-6-PK

$32.80

Sample packs consists of ten (10) Intellivents and a 6" Intellitube. Grooved PTFE Tube which holds Norstar's 3/4" Intellivent (Part Number KC401852). Tube does not need to be taken from mold. The reaming and groove ensures fit and locks the Intellivent in place.

Other sizes - 8", and 10" - available of Intellitubes:
Part Number KC5752-8-PK
Part Number KC5752-10-PK

Intellivent/Intellitube Sample Pack - 8", KC401852-8-PK

Intellivent/Intellitube Sample Pack - 8", KC401852-8-PK

$33.50

Sample pack consists of ten (10) Intellivents and one (1) Intellitube. Grooved PTFE Tube which holds Norstar's 3/4" Intellivent (Part Number KC401852). Tube does not need to be taken from mold. The reaming and groove ensures fit and locks the Intellivent in place.

Other sizes - 6" and 10" - available of Intellitubes:
Part Number KC5752-6-PK
Part Number KC5752-10-PK

Intellivent/Intellitube Sample Pack - 10", KC401852-10-PK

Intellivent/Intellitube Sample Pack - 10", KC401852-10-PK

$34.80

Sample pack consists of ten (10) Intellivents and one (1) 10'' Intellitube. Grooved PTFE Tube which holds Norstar's 3/4" Intellivent (Part Number KC401852). Tube does not need to be taken from mold. The reaming and groove ensures fit and locks the Intellivent in place.

Other sizes - 6" and 8" - available of Intellitubes:
Part Number KC5752-6-PK
Part Number KC5752-8-PK

Intellicutter, 3/4 inch, KC4052

$187.50

This cutter will allow you to cut our Teflon tube (KC5752) to accept the intellivent (KC401852). It cuts a recess into the Teflon about .200” deep.

Intellivent has been designed to fit inside an appropriately sized PTFE boss. The OD of the intellivent sits snugly on the ID of the Teflon tube. When fitting the intellivent, please make sure that the wedge of the Intellivent is sitting uniformly against the ID of the Teflon tube you are using. An incorrectly installed Intellivent may have folds or kinks in the wedge that may impact the performance. To improve the security of the Intellivent event, we recommend that you use one of our intellicutters to size and recess the vent tube that you are using.

For a 360° view of a line drawing of an intellicutter, please go to this website:
https://myhub.autodesk360.com/ue2daed1b/g/shares/SH9285eQTcf875d3c5398a62f987c25b7e5d