Home > Production Related Parts > Retex Tools
Sort By:
Page of 1
Retex Tool, KC4010-1 (one tool)
Retex Tool, KC4010-1 (one tool)
$65.00

One piece only for this part number.
Please specify shape: round, triangle, or square.
Please specify finish: 550 shot peen, 330 shot peen, or sand blast.

Retex Tools are designed to repair plastic parts that may have become damaged during or after molding. Using Retex Tools can reduce scrap rates caused by scratches or gouges that occur after the molding process. They have been designed and manufactured to impart typical mold finishes such as shot peen and sandblast finishes that are utilized in the manufacturing of rotational molding tooling.

Retex Tools are coated with a permanent release coating so there is no need to use any release agent.
Please allow for a two weeks for lead time.

To order a set of three (3) Retex Tools, see KC4010.
more info
Retex Tool (Set of 3), KC4010
Retex Tool (Set of 3), KC4010
$175.00

Retex Tools are designed to repair plastic parts that may have become damaged during or after molding. Using Retex Tools can reduce scrap rates caused by scratches or gouges that occur after the molding process. They have been designed and manufactured to impart typical mold finishes such as shot peen and sandblast finishes that are utilized in the manufacturing of rotational molding tooling. Retex Tools are coated with a permanent release coating so there is no need to use any release agent.

Please allow two weeks for a lead time.

Mix or match to make a set.
Please specify which shape (round, triangle, or square) and what which finish for each shape (550 shot peen, 330 shot peen, or sand blast).
more info
Retex Roller, KC4021-1
Retex Roller, KC4021-1
$200.00

One handle, one roller.

Retex Roller is designed to be used to repair plastic parts that may have become damaged during or after molding.

Using the Retex Roller can reduce scrap rates caused by scratches or gouges in the part. It has been designed and manufactured to impart on the plastic part typical mold finishes such as shot peen and sanded finishes that are utilized in the manufacturing of rotational mold tooling. In this way, blemishes can be blended into the surrounding areas saving what was going to be a scrap part. (Please specify finish - 550 shot peen, 330 shot peen or sand blast ).

Superficial scratches will require only a slight heating of the plastic part so as to soften the surface. Then the Retex Roller can be used to flow the surface plastic into the scratch at the same time imparting the appropriate texture.

Retex Rollers are coated with a permanent release coating so there is no need to use any release agent.

For deep scratches, gouges or holes, it is recommended that Patch 'N GO™ from Mold-In Graphics be used to first fill in the imperfection, then heat to cure it and quickly use the appropriate Retex Roller to impart the proper texture to the surface of the part.

Start salvaging your scrap parts. Order your Retex Roller today.

Check out our little video on this product
more info
Retex Roller, KC4021
Retex Roller, KC4021
$225.00

One handle, three rollers.

Retex Roller is designed to be used to repair plastic parts that may have become damaged during or after molding.

Using the Retex Roller can reduce scrap rates caused by scratches or gouges in the part. It has been designed and manufactured to impart on the plastic part typical mold finishes such as shot peen and sanded finishes that are utilized in the manufacturing of rotational mold tooling. In this way, blemishes can be blended into the surrounding areas saving what was going to be a scrap part. (Comes with the following finishes: One 550 shot peen, one 330 shot peen and one sand blast).

Superficial scratches will require only a slight heating of the plastic part so as to soften the surface.
Then the Retex Roller can be used to flow the surface plastic into the scratch at the same time imparting the appropriate texture.

Retex Rollers are coated with a permanent release coating so there is no need to use any release agent.

For deep scratches, gouges or holes, it is recommended that Patch 'N Go™ from Mold-In Graphics be used to first fill in the imperfection, then heat to cure it and quickly use the appropriate Retex Roller to impart the proper texture to the surface of the part.

Start salvaging your scrap parts. Order your Retex Roller today.

Check out our little video on this product
more info